Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
Corvair Center Forum :  Corvair Center Phorum The fastest message board... ever.
Corvair Center 
Pages: Previous12
Current Page: 2 of 2
Re: 215 in my 65 monza
Date: January 29, 2018 09:36AM

215 gives the vair the most factory feel and best balance IMHO. While the motor itself is older design, you can get them up to 4.6 in Rover variant and in some cases 5.0L not sure if that was just in the TVR or range rover as well. I have a datsun 1200 I have been looking for a 215 for.. its a great motor.

Options: ReplyQuote
Re: 215 in my 65 monza
Posted by: American Mel ()
Date: January 29, 2018 01:47PM

Jim Stukenborg Wrote:
-------------------------------------------------------
> Dooee, here is an OSHA approved cover for that
> crank pulley. The pulley is fully enclosed behind
> the flap. Jim
>
> [i64.tinypic.com]


Flap???
That thing looks like .... eye popping smiley
Well, forget about what it looks like.
Just know that it would not be polite to discuss that here on a family friendly forum!

.
-----------------------------------------------
WA. state, 1 mile south of the Canadian border,
I am not at the end of the world, but you can see it from here.
'66 Monza Coupe - 4spd, 140 Daily driver beater
'67 Monza Vert. - PG, 140 Daily driver beater

Options: ReplyQuote
Re: 215 in my 65 monza
Posted by: kenvair ()
Date: January 29, 2018 07:42PM

Regarding crank pulley interference with rear grill: Moving the 215 engine 2 inches forward allowed my rear grill to look like this. Ken Arnold

Attachments:
Options: ReplyQuote
Re: 215 in my 65 monza
Posted by: dooee567 ()
Date: January 30, 2018 04:49AM

Drivers if responded to my questions thank you

Options: ReplyQuote
Re: 215 in my 65 monza
Posted by: Spectre ()
Date: January 30, 2018 04:52AM

I always liked that car Ken.

David Clamp


1965 Corsa convertible - 140 4spd/3.55/AM-FM

2013 Mustang GT convertible - 5.0, 6spd auto, Procharger i-1

2003 Miata SE - 6spd manual (wife's toy)

"Victory is mine!" - SG

Oklahoma City, OK

Click for Oklahoma City, Oklahoma Forecast

Options: ReplyQuote
Re: 215 in my 65 monza
Posted by: dooee567 ()
Date: January 30, 2018 05:18AM

To those who have responded to my questions thank you

for those who are running a manual trans how are you setting up your
pressure plate and flywheel to match up with your corvair starter gears?

Anyone think it's possible to modify a Buick flexplate to hook up to the corvair torque converter and spacers on the flexplate to help line up the starter gears?

Options: ReplyQuote
Re: 215 in my 65 monza
Posted by: gmgmtl ()
Date: January 30, 2018 07:22AM

The late Karl Cozad covered his 215 installation in an interview back in 2013.
GMoore


Options: ReplyQuote
Re: 215 in my 65 monza
Date: January 30, 2018 07:58AM

Not sure as to why the issues with pulleys and clearance, perhaps its the pulley type. our 215 (now Craig) never had issues nor does the LS1.



Options: ReplyQuote
Re: 215 in my 65 monza
Posted by: cnicol ()
Date: January 30, 2018 08:57AM

In my case, when I installed the ex-McCreery 215 (255) in my '66, the pulley clearance "problem" was caused by my use of a wider "serpentine" belt pulley system. I went with the serpentine belt because of my need to run an A/C compressor. In my assessment, a single 7/16" v-belt would have been overtaxed driving the 55-amp alternator, water pump, and A/C compressor.

If I didn't have A/C, I would have used the single V-groove crank pulley and there wouldn't have been an issue with the pulley touching the rear air grille. However, I'm pretty sure all 215 conversions still require notching of the rear frame rail.

Craig N. Coeur d'Alene ID.
66 Black Monza 4dr, 4.2L V8 49k
61 Seamist Jade Rampside 140 PG
60 Monza coupe (sold, sniff sniff)
66 Sprint Corsa convt - First car! Re-purchased 43 years later
2+2 gnatsuM 5691

+17 Tons of parts

Attachments:
Options: ReplyQuote
Pages: Previous12
Current Page: 2 of 2


Sorry, only registered users may post in this forum.
This forum powered by Phorum.