Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
Corvair Center Forum :  Corvair Center Phorum The fastest message board... ever.
Corvair Center 
180 Sheet metal?
Posted by: JerryM ()
Date: January 26, 2018 05:18AM

What pieces of sheet metal and shrouding are unique to LM turbo's and how do I identify them?

Options: ReplyQuote
Re: 180 Sheet metal?
Posted by: steve c goodman ()
Date: January 26, 2018 05:34AM

Pass side heater outlet (2 pieces)
Front and pass side tins from eng to body
Fan shroud
Exh pipe in/out collar retainers

best wishes, Steve
Rear Engine Spec. Inc. Golden, Colo.

1962 spyder 3.0L turbo---1965 Crown V8
1967 monza 110/4---1968 monza 110/4
1971 amante gt 110/4
CORSA/RMC/PPCC

Options: ReplyQuote
Re: 180 Sheet metal?
Posted by: Wagon Master ()
Date: January 26, 2018 05:46AM

Rear tail light panel. Has an half moon cut out for the exhaust to exit.

Options: ReplyQuote
Re: 180 Sheet metal?
Posted by: steve c goodman ()
Date: January 26, 2018 05:55AM

Good point I was thinking only engine pieces

best wishes, Steve
Rear Engine Spec. Inc. Golden, Colo.

1962 spyder 3.0L turbo---1965 Crown V8
1967 monza 110/4---1968 monza 110/4
1971 amante gt 110/4
CORSA/RMC/PPCC

Options: ReplyQuote
Re: 180 Sheet metal?
Posted by: JerryM ()
Date: January 26, 2018 07:14AM

steve c goodman Wrote:
-------------------------------------------------------
> Pass side heater outlet (2 pieces)
> Front and pass side tins from eng to body
> Fan shroud
> Exh pipe in/out collar retainers


What's different about those pieces?

Options: ReplyQuote
Re: 180 Sheet metal?
Posted by: steve c goodman ()
Date: January 26, 2018 07:37AM

JerryM Wrote:
-------------------------------------------------------
> steve c goodman Wrote:
> --------------------------------------------------
> -----
> > Pass side heater outlet (2 pieces)

heater outlet is shaped differently to clear the exhaust
inlet pipe to turbo

> > Front and pass side tins from eng to body

Holes are cut into front pass side of both pieces to allow
enter/exit of exhaust plumbing to turbo

> > Fan shroud

Fresh air outlet is on dr side of fan shroud instead of
behind turbo as carb car is

> > Exh pipe in/out collar retainers

The retainers clamp the insulating collars that surround
the inlet/outlet pipes.

>
>
> What's different about those pieces?

best wishes, Steve
Rear Engine Spec. Inc. Golden, Colo.

1962 spyder 3.0L turbo---1965 Crown V8
1967 monza 110/4---1968 monza 110/4
1971 amante gt 110/4
CORSA/RMC/PPCC

Options: ReplyQuote
Re: 180 Sheet metal?
Posted by: JerryM ()
Date: January 26, 2018 08:03AM

steve c goodman Wrote:
-------------------------------------------------------
> JerryM Wrote:
> --------------------------------------------------
> -----
> > steve c goodman Wrote:
> >
> --------------------------------------------------
>
> > -----
> > > Pass side heater outlet (2 pieces)
>
> heater outlet is shaped differently to clear the
> exhaust
> inlet pipe to turbo
>
> > > Front and pass side tins from eng to body
>
> Holes are cut into front pass side of both pieces
> to allow
> enter/exit of exhaust plumbing to turbo
>
> > > Fan shroud
>
> Fresh air outlet is on dr side of fan shroud
> instead of
> behind turbo as carb car is
>
> > > Exh pipe in/out collar retainers
>
> The retainers clamp the insulating collars that
> surround
> the inlet/outlet pipes.
>
> >
> >
> > What's different about those pieces?

thumbs up Thanks!

Options: ReplyQuote


Sorry, only registered users may post in this forum.
This forum powered by Phorum.