Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
Corvair Center Forum :  Corvair Center Phorum The fastest message board... ever.
Corvair Center 
FOUND!!-- EM Axle Flange
Posted by: MoxyRamone ()
Date: January 15, 2018 01:09PM

I need an axle flange. My parts car had a set and the drivers side came off with a few taps with a hammer. The passenger side will not budge. Heat, penetrating oil, prayer... nothing is working. It's looking like it will be a lot easier to just source a used one.

Does anyone have one they are willing to part with?

John Carver
Landrum, South Carolina

1964 Monza Convertible



Edited 1 time(s). Last edit at 01/15/2018 08:27PM by MattNall.

Attachments:
Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: Wagon Master ()
Date: January 15, 2018 01:23PM

If the drivers side came off with "A few taps of a hammer" I'd start looking for a pair and replace them both.

'29 Ford Model A Tudor
'61 700 Lakewood 110 4 speed
'69 Monza Convert. 140 Auto.
'70 Dodge Challenger R/T 440 4 speed

Been aircooled since 1973
Northwest Ohio

Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: MoxyRamone ()
Date: January 15, 2018 01:36PM

It was more like several whacks with a sledgehammer.

John Carver
Landrum, South Carolina

1964 Monza Convertible

Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: kenvair ()
Date: January 15, 2018 02:37PM

PM sent

Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: irfgt ()
Date: January 15, 2018 04:34PM

MoxyRamone Wrote:
-------------------------------------------------------
> I need an axle flange. My parts car had a set and
> the drivers side came off with a few taps with a
> hammer. The passenger side will not budge. Heat,
> penetrating oil, prayer... nothing is working.
> It's looking like it will be a lot easier to just
> source a used one.
>
> Does anyone have one they are willing to part
> with?


Are you familiar with Jerry Jennings Garage in Landrum? He has a bunch of all year Corvairs right there in Landrum. Excellent parts source.

Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: davemotohead ()
Date: January 15, 2018 04:54PM

I have a set blasted clean setting on the bench if you strike out with others.





Email me at: Dave Motohead

1960 4dr sedan caveman car
1961 Rampside (Chetside)
1962 Rampside (Barnside)
1962 Short Rampside (Shortside)
1962 Monza 700 Wagon
1963 Monza 900 coup (General Nader)

-----------------------------------
Rust Free Lancaster Ca

Attachments:
Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: Timothy Shortle ()
Date: January 15, 2018 05:08PM

Those that DaveM. has look quite fine. If they are as good as the 2 I bought from him a year ago, you will have no problem. And his are clean, tested, (primered) and ready to go. Oh and for me they were VERY affordable.

Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: Frank DuVal ()
Date: January 15, 2018 06:44PM

If I ever got one off with a hammer, it was a miracle or worn on the splines. I always need to use the tool. It is available from Clarks, C3100.

Even with the tool I have needed a torch many times. One parts car I gave up and cut the axle in hopes of the bearing being good (it was!).thumbs up

A hammer can bend the yoke.

Dave, you west coast people have the nicest rust free parts! I bought some from Charie Dye when he made it to the Carlisle PA convention. I never saw such rust free yokes before!

Frank DuVal

Fredericksburg, VA

Options: ReplyQuote
Re: Need Part -- EM Axle Flange
Posted by: MoxyRamone ()
Date: January 15, 2018 07:11PM

Thanks everyone, I found one.

Options: ReplyQuote


Sorry, only registered users may post in this forum.
This forum powered by Phorum.