Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
Corvair Center Forum :  Corvair Center Phorum The fastest message board... ever.
Corvair Center 
Oil Priming Tool - Revisited
Posted by: vairmech ()
Date: December 18, 2017 09:54AM

I have more distributors than I know what to do with and I will make and ship a few for $25 ppd, in the USA. These will not be rebuilt nor will they be turbo or 140 distributor numbers, they will be clean and useable similar to what I pictured in the other thread.

Any interest?

forsale

Ken Hand
Handy Car Care
248 613 8586

Vairmech@aol.com

Options: ReplyQuote
Re: Oil Priming Tool - Revisited
Posted by: azdave ()
Date: December 18, 2017 10:12AM

How much to make one for a reversed Corvair engine?

grinning smiley grinning smiley grinning smiley


Dave W. / Gilbert Arizona
66 Corsa 140 4-speed w/factory A/C
66 Corsa 140 4-speed w/factory A/C
66 Corsa 140 4-speed
65 Corsa 140 4-speed
66 Corsa 455 Toro V8
65 Monza 455 Toro V8
65 Monza 110 Convertible
65 Monza 4DR 140 PG w/factory A/C
65 Monza 4DR EJ20T w/5-speed




Options: ReplyQuote
Re: Oil Priming Tool - Revisited
Posted by: steve c goodman ()
Date: December 18, 2017 10:27AM

azdave Wrote:
-------------------------------------------------------
> How much to make one for a reversed Corvair
> engine?
>
> grinning smiley grinning smiley grinning smiley

Trick question Ken, everyone knows you just turn it upside down ggg

best wishes, Steve
Rear Engine Spec. Inc. Golden, Colo.

1962 spyder 3.0L turbo---1965 Crown V8
1967 monza 110/4---1968 monza 110/4
1971 amante gt 110/4
CORSA/RMC/PPCC

Options: ReplyQuote
Re: Oil Priming Tool - Revisited
Posted by: vairmech ()
Date: December 18, 2017 10:45AM

Oh NO! That is 20% more!!!!! It takes more to make it. I have to turn the lathe backwards and everything!

Ken Hand
Handy Car Care
248 613 8586

Vairmech@aol.com

Options: ReplyQuote
Re: Oil Priming Tool - Revisited
Posted by: davemotohead ()
Date: December 18, 2017 01:25PM

I want one for a High volume oil pump running Recommended thick oil.





Email me at: Dave Motohead

1960 4dr sedan caveman car
1961 Rampside (Chetside)
1962 Rampside (Barnside)
1962 Short Rampside (Shortside)
1962 Monza 700 Wagon
1963 Monza 900 coup (General Nader)

-----------------------------------
Rust Free Lancaster Ca

Attachments:
Options: ReplyQuote
Re: Oil Priming Tool - Revisited
Posted by: Seth Emerson ()
Date: December 18, 2017 02:50PM

That takes the special Chromalloy steel shaft. But with the unsulphered product, the flat tappets will pre-maturely wear. You would have a sticky situation.

Seth Emerson

Check my new Performance Corvair Web site [www.perfvair.com]

Options: ReplyQuote
Re: Oil Priming Tool - Revisited
Posted by: corvair66 ()
Date: December 19, 2017 06:19AM

Ken,
I'm in. Just about to that point on my winter rebuild, Alays nice to have the right tool.

Dave Huntoon CNM/CORSA in the moutons of New Mexico

Options: ReplyQuote


Sorry, only registered users may post in this forum.
This forum powered by Phorum.