Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
Corvair Center Forum :  Corvair Center Phorum The fastest message board... ever.
Corvair Center 
Current Page: 2 of 3
Re: 64 Rampside
Posted by: ac1948 ()
Date: December 02, 2017 08:55AM

Tim, here are the pics of heater delete plates in eng. compartment and floor board. Will get lower ones later. Jerry

Attachments:


Options: ReplyQuote
Re: 64 Rampside
Posted by: Pedigo ()
Date: December 02, 2017 08:58AM

I love that uncut (but perforated,just in case) floor mat!
That's a cool feature.

Options: ReplyQuote
Re: 64 Rampside
Posted by: Timothy Shortle ()
Date: December 02, 2017 11:24AM

Thank you Jerry. I like em. I see the engine compartment parts are the same as a gas heater equipped vehicle (probably not 1960 though).
I am sure not many vehicles like that were sold here in Colorado.

Options: ReplyQuote
Re: 64 Rampside
Posted by: Vern in Bend ()
Date: December 02, 2017 04:50PM

There should be a block-off plate under the rubber mat at the perforations, (defrost air) and another in the center front of the 'seat riser' (cab air).

I had to make those when I converted my FCs from air to gas heat.

Regards, Vern

Bend, Oregon

'64 Corvan, daily driver - 43 years
'64 Rampside, personal driver - 25 years
'67 Monza Cpe, original owner - 33k miles
'81 Vanagon high-top panel van

Options: ReplyQuote
Re: 64 Rampside
Posted by: Pedigo ()
Date: December 02, 2017 05:11PM

I can only imagine how sweet it might be,to install new right/front shocks.ggg

Options: ReplyQuote
Re: 64 Rampside
Posted by: Vern in Bend ()
Date: December 02, 2017 08:03PM

I don't recall it being difficult to remove/replace that air duct (when my FC's had them) in order to change the shock, and I did do that.

BTW, the assembly manual shows all of the covers that would be used for heater delete - even has the part #'s for them, and shows where to put a 'sealing' bolt into holes that would be open to the outside if not used to mount a heater part. In my '64 manual they are on pages in the 90's.

Regards, Vern

Bend, Oregon

'64 Corvan, daily driver - 43 years
'64 Rampside, personal driver - 25 years
'67 Monza Cpe, original owner - 33k miles
'81 Vanagon high-top panel van

Options: ReplyQuote
Re: 64 Rampside
Posted by: ac1948 ()
Date: January 19, 2018 11:44AM

A little progress today. Painted the hubcaps.

Jerry Murray
Charleston, SC

63 Rampside, PG,110

63 Greenbrier, PG, 110

64 Rampside, 110, 4 speed

Attachments:

Options: ReplyQuote
Re: 64 Rampside
Posted by: Timothy Shortle ()
Date: January 19, 2018 12:34PM

And they sure look great Jerry. Keep up the good work. That one is a keeper (but sure would be hard to drive in winter in CO.)

Options: ReplyQuote
Re: 64 Rampside
Posted by: ac1948 ()
Date: March 01, 2018 09:24AM

Primed the back half of the truck today. Sure is great to work on rust free metal.

Jerry Murray
Charleston, SC

63 Rampside, PG,110

63 Greenbrier, PG, 110

64 Rampside, 110, 4 speed

Attachments:


Options: ReplyQuote
Re: 64 Rampside
Posted by: MattNall ()
Date: March 01, 2018 09:36AM

Looks pretty solid and straight!





MODERATOR
Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast
Click HERE for My Website...Click HERE for My TechPages!
..............................110-PG.................................................Webered-Turbo

Options: ReplyQuote
Re: 64 Rampside
Posted by: ac1948 ()
Date: March 16, 2018 03:10PM

Painted a few pieces today.

Jerry Murray
Charleston, SC

63 Rampside, PG,110

63 Greenbrier, PG, 110

64 Rampside, 110, 4 speed

Attachments:


Options: ReplyQuote
Re: 64 Rampside
Posted by: MattNall ()
Date: March 16, 2018 03:31PM

Came out Nice!





MODERATOR
Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast
Click HERE for My Website...Click HERE for My TechPages!
..............................110-PG.................................................Webered-Turbo

Options: ReplyQuote
Re: 64 Rampside
Posted by: corventure Dave ()
Date: March 16, 2018 04:16PM

Looking great!

Corventure Dave

Options: ReplyQuote
Re: 64 Rampside
Posted by: ac1948 ()
Date: March 25, 2018 10:36AM

Refurbished the vent window frames this weekend.Not my favorite project. PITA

Jerry Murray
Charleston, SC

63 Rampside, PG,110

63 Greenbrier, PG, 110

64 Rampside, 110, 4 speed

Options: ReplyQuote
Re: 64 Rampside
Posted by: MattNall ()
Date: March 25, 2018 11:39AM

As many have reported!!!





MODERATOR
Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast
Click HERE for My Website...Click HERE for My TechPages!
..............................110-PG.................................................Webered-Turbo

Options: ReplyQuote
Re: 64 Rampside
Posted by: ac1948 ()
Date: March 26, 2018 01:59PM

Went to painter today.

Jerry Murray
Charleston, SC

63 Rampside, PG,110

63 Greenbrier, PG, 110

64 Rampside, 110, 4 speed

Attachments:
Options: ReplyQuote
Re: 64 Rampside
Posted by: MattNall ()
Date: March 26, 2018 02:34PM

Can't wait to see it next time!





MODERATOR
Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast
Click HERE for My Website...Click HERE for My TechPages!
..............................110-PG.................................................Webered-Turbo

Options: ReplyQuote
Re: 64 Rampside
Posted by: ac1948 ()
Date: April 11, 2018 03:18PM

Back from paint and reassembly started.

Jerry Murray
Charleston, SC

63 Rampside, PG,110

63 Greenbrier, PG, 110

64 Rampside, 110, 4 speed

Attachments:


Options: ReplyQuote
Re: 64 Rampside
Posted by: MattNall ()
Date: April 11, 2018 03:28PM

You can be proud!





MODERATOR
Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast
Click HERE for My Website...Click HERE for My TechPages!
..............................110-PG.................................................Webered-Turbo

Options: ReplyQuote
Re: 64 Rampside
Posted by: The Stig ()
Date: April 11, 2018 04:54PM

Very nice!!!

Options: ReplyQuote
Current Page: 2 of 3


Sorry, only registered users may post in this forum.
This forum powered by Phorum.