Should side window regulator gears and guides/rollers be lubed?

Brice

66 Corsa Turbo Convertible

Bozeman, Montana

Sure...white lithium grease IIRC

MODERATOR
Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast
Click HERE for My Website...Click HERE for My TechPages!
...............110-PG.................................................Webered-Turbo

That sounds good to me. That is what the original lube looked like but was more like adhesive!

Brice

66 Corsa Turbo Convertible

Bozeman, Montana

50 years will do that!

MODERATOR
Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast
Click HERE for My Website...Click HERE for My TechPages!
...............110-PG.................................................Webered-Turbo

50 years, I recently had to remove the lube from my 98 Park Avenue and re-apply white lithium lube. 18 years and it was like cement. I had to lower the window pulling down on the glass while pushing the switch. Now, zip, done.

I've always used white lithium lube for window parts.

Frank DuVal

Fredericksburg, VA

White lithium was used, but it tends to dry out after five years (design life span of 60's cars). Eventually it binds things up.

There are much better lubricants now. If the car is going to be used in adverse weather you can use water resistant marine bearing grease used on boat trailers.

I used axle grease on the beetles regulators...

However, I was over zealous and always got a little red and tack on the window when ever I rolled it down and up again.

Kyle

White is the preferred for color, but any multipurpose #2 grease will do. I once asked the Nissan dealer why he bought my white food grade grease, and he said customers did not like to see colored grease on the hinges, door locks, etc.

Restoration in Bolivia
Richard's Mini Pickup
Richard's Corvair
Richard's Renault Dauphine

Selection of the Right Motor Oil for the Corvair
Selection of the right transmission oil for the Corvair
How to polish and restore stainless and aluminum trim

I removed mine, soaked them in solvent, then still had to scrape off the old waxy OEM grease that was hardened in place. I relubed w/ synthentic wheel bearing grease on the splines and spray synthetic lube for the pivots. Works smooth as butter now!

Nick
_______________________________________________________________________
1964 Monza Spyder Convertible #435 - Rotisserie restored - SOLD ON BRING A TRAILER 4/30/2019 - Check out my restoration thread here: [corvaircenter.com]
Thanks to all the awesome CCF, CF, COG, and CORSA members who helped me with the restoration!
Other fun stuff - 1997 Spec Boxster Race Car #94 - 2018 Panamera Turbo ST -- 2022 Macan GTS -- 2019 Golf R 6MT -- 2015 S60 P* -- 2021 F-250 HCTTP Diesel -- Haulmark race trailer
Northern Colorado, USA

[www.amazon.com]

This is what I use after I clean things up.

J.O.

65 Corsa Turbo Vert
79 Honda XL 500S
69 Honda CL 160 D
2010 BMW F 650 GS
2003 Bounder 36D
2023 KIA K5 GT/GT1 turbo-AKA ZIPPY II (wife,s car)
69 Newport Holiday Sailboat
Baja 150 dune buggy cart
Coleman HS 500 UTV
2016 KIA Sorento SXL Turbo

Bethlehem,Pa

That works great on garage door hinges and rollers............

I use motorcycle chain lube in the spray can. It soaks into all the right places then turns into grease when the propellant dries up. It is great for door hinges and almost anything that moves and does not leave a residue.