Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
Corvair Center Forum :  Corvair Center Phorum The fastest message board... ever.
Corvair Center 
Current Page: 181 of 181
Re: What did you WORK ON / DO....to your Corvair today?
Date: November 08, 2018 08:29AM

3rd Step to Period Performance

Quick shift
3.55 Sginaw
Headers.

Next step
Fast sterring short arms
Offenhauser Baffled Oilpan + Clerks Pickup
Off.Valve Covers.

Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Date: November 09, 2018 06:47AM

Step by Step on my Projekt Car.
just to feel something while Work on the Car.

Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: Vairefast ()
Date: November 11, 2018 02:07PM

Put together my next toploader transmission for my V8 corvair. Changing gear ratios.

3.25 1st, 1.92 2nd, 1.00 3rd, 0.78 4th and 3.25 Rev. now

3.07 1st, 1.72 2nd, 1.00 3rd, 0.70 4th, and 3.07 Rev. new one.

Darrin
65 Crown
68 Monza convert

Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: viewmaster ()
Date: November 11, 2018 05:35PM

Took the cut, stock coils, out of my project car front end, just to see how it looked on my driver. WOW!!!! What a difference!!! When driving, hood is way down there, it seems. I like the profile. Looks like PO cut stock coils, 2".

-m



Mike
'65 '500' Sedan 110 PG
'65 Monza Sedan turbo'd 110 SU conversion
Fresno, CA

Attachments:

Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: MattNall ()
Date: November 11, 2018 05:41PM

Always look better low in rear.....lower in front!

Attachments:
Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: Phil Dally ()
Date: November 15, 2018 01:22PM

Loaded Schrum II motor in the truck.

Delivery to Galli residence manana.

Along with all proper accoutrements.

Schrum I heads to Slover next week.

Attachments:


Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: Gregory_Miller ()
Date: November 17, 2018 12:23PM

Installed my new reverse light switch, decided where the triple coil pack is going to live, and painted the base gloss black, it was metallic blue. Measured the wire Seth sent me for the lengths of the new plug set I need. Started integrating the FI and SDS-4 wiring into the main harness but need to buy more electrical tape. Installed the new brake and clutch pedal pads.

Greg Miller
Eugene, Oregon

Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: The Stig ()
Date: November 17, 2018 04:18PM

My upholsterer friends wasted no time on the seat for the Ugly Rampy Im working on. Wheels are at the powder coater. I better get busy on getting its engine swapped.






Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: MattNall ()
Date: November 17, 2018 10:59PM

Finally installed my Custom Quick Disconnect with Grant Sport Wheel and working horn with no wire!

Wheel [ 3" dish ] is 1/2" Closer to dash compared to stock Monza [ 7" dish ].

Now I can switch wheels in 30 seconds and remove it should I need to get under dash...plus no more banging my knee! [ 16" versus 14" ]



Edited 2 time(s). Last edit at 11/17/2018 11:10PM by MattNall.

Attachments:


Options: ReplyQuote
Re: What did you WORK ON / DO....to your Corvair today?
Posted by: Gregory_Miller ()
Date: November 19, 2018 10:35AM

Re-taped all my engine bay wiring harness, integrating the SDS wires into the harness. Need bolts and some angle bracket to support one end of the triple coil; pack. Got the MAP sensor installed, but still need to route engine vacuum to it.

Greg Miller
Eugene, Oregon

Options: ReplyQuote
Current Page: 181 of 181


Sorry, only registered users may post in this forum.
This forum powered by Phorum.