Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“Performance
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
Corvair Center Forum :  Corvair Center Phorum The fastest message board... ever.
Corvair Center 
Pages: Previous12345
Current Page: 5 of 5
Re: SHOW US your Homemade Corvair parts/tools!
Posted by: Lane66m ()
Date: January 21, 2018 01:03AM

This discussion is listed in the FAQs, but you have to really look for it. It is in the Books / Websites / Diagrams you may need: section. Then after you click on that link, you cliCk on the link that one brings up and you are there.

Might be easier to make this discussion one you follow and have it listed in your Control Center.

Al Lane
Ellabell GA

1966 Monza Coupe, 110 hp, 4 Spd
1968 Camaro SS Coupe 350 CI 295+ HP PG
1964 Greenbrier Deluxe, 6 dr, 80 hp car engine, PG
2015 Chevrolet Malibu 2LT
2015 GMC Sierra SLT Crew Cab
1947 Farmall A tractor 15 hp


Options: ReplyQuote
Re: SHOW US your Homemade Corvair parts/tools!
Posted by: Lane66m ()
Date: January 21, 2018 03:29AM

The issue is holding the alternator fan nut / armature shaft in order to apply book value torque to the assembly. Here is shown 2 ways.

Another way not shown would be a 15/16 box-end crows-foot wrench. With it you need to have it attached 90 degrees to the torque wrench or recalculate the applied torque due to the added length to the torque wrench to connect to the fan nut.

Al Lane
Ellabell GA

1966 Monza Coupe, 110 hp, 4 Spd
1968 Camaro SS Coupe 350 CI 295+ HP PG
1964 Greenbrier Deluxe, 6 dr, 80 hp car engine, PG
2015 Chevrolet Malibu 2LT
2015 GMC Sierra SLT Crew Cab
1947 Farmall A tractor 15 hp


Attachments:
Options: ReplyQuote
Re: SHOW US your Homemade Corvair parts/tools!
Posted by: martyscarr ()
Date: January 30, 2018 12:34AM

Here's a tool for intalling a throwout bearing shaft or stator shaft in a differential. The cone portion is movable, it centers the tool in the differential and you drive in the shaft until it's seated.

Attachments:
Options: ReplyQuote
Re: SHOW US your Homemade Corvair parts/tools!
Posted by: martyscarr ()
Date: January 30, 2018 12:41AM

This tool is to remove the pinion adjuster sleeve on a powerglide differential. Last year I worked on a PG diff that had a very tight pinion adjuster. I couldn't break the adjuster loose and didn't want to use the hammer on it, so I made this tool. The threaded rod goes through the pinion shaft and tightens the tool to the adjuster, a 1/2" breaker bar is used to turn the tool. I have Rex Johnson's diff tools for the side adjuster and manual trans pinion adjuster, but this is one he doesn't offer.



Edited 1 time(s). Last edit at 01/30/2018 12:43AM by martyscarr.

Attachments:
Options: ReplyQuote
Pages: Previous12345
Current Page: 5 of 5


Sorry, only registered users may post in this forum.
This forum powered by Phorum.