 | |||||
 |
 |
 |
 |
 |
 |
 | |||||
Corvair Center Forum :
Corvair Center Phorum - presented by CORSA
Corvair Center
What screw goes here? Right air cleaner support
Posted by:
PequotMonza64
()
Date: June 17, 2022 10:04AM
First of all, apologies for being testy about screw identification with Frank DuVal and RobertC a while back, because now I have a screw ID question. And sometimes it is hard to tell the difference, Frank, when those small screws are involved, especially if you've been painting.
Where the RH passenger side air filter support attaches over the engine shroud and into the aluminum cylinder head, there are two threaded holes larger than 1/4-20. What bolts go here? The big ones pictured below begin to thread, but I don't want to force them. I have cleaned the thread holes with blaster and a Q-tip and wire wheeled the bolt, but still no go. I have some taps but am hesitant to mess with aluminum if I don't know the correct size beforehand.
Looking at some "before" photos I took, it looks like the big bolts should thread in there.
Help? Am I missing two bolts? Also, I have three of these big one, not two...
Glen in Ohio
1964 Monza Sedan Powerglide 110 hp
Low mileage survivor, stock as delivered
Records back to 1967 in Pequot Lakes, Minnesota
Original dealer Mike Turk's in East Liverpool, Ohio
Located in Cleveland, Ohio area
Where the RH passenger side air filter support attaches over the engine shroud and into the aluminum cylinder head, there are two threaded holes larger than 1/4-20. What bolts go here? The big ones pictured below begin to thread, but I don't want to force them. I have cleaned the thread holes with blaster and a Q-tip and wire wheeled the bolt, but still no go. I have some taps but am hesitant to mess with aluminum if I don't know the correct size beforehand.
Looking at some "before" photos I took, it looks like the big bolts should thread in there.
Help? Am I missing two bolts? Also, I have three of these big one, not two...
Glen in Ohio
1964 Monza Sedan Powerglide 110 hp
Low mileage survivor, stock as delivered
Records back to 1967 in Pequot Lakes, Minnesota
Original dealer Mike Turk's in East Liverpool, Ohio
Located in Cleveland, Ohio area
Re: What screw goes here? Right air cleaner support
Posted by:
Timothy Shortle
()
Date: June 17, 2022 10:06AM
They are the "big" ones. 3/8 X 16. You show 1 of them.
Re: What screw goes here? Right air cleaner support
Posted by:
PequotMonza64
()
Date: June 17, 2022 10:47AM
Thanks, Tim. I found a 13 minute video I took of the whole engine compartment still together, and it looks like those are the bolts in the video, too.
Glen in Ohio
1964 Monza Sedan Powerglide 110 hp
Low mileage survivor, stock as delivered
Records back to 1967 in Pequot Lakes, Minnesota
Original dealer Mike Turk's in East Liverpool, Ohio
Located in Cleveland, Ohio area
Glen in Ohio
1964 Monza Sedan Powerglide 110 hp
Low mileage survivor, stock as delivered
Records back to 1967 in Pequot Lakes, Minnesota
Original dealer Mike Turk's in East Liverpool, Ohio
Located in Cleveland, Ohio area
Re: What screw goes here? Right air cleaner support
Posted by:
Lane66m
()
Date: June 17, 2022 12:41PM
If still original heads, forward 2 bolts are 3/8-16. Aft 3 are 1/4-20. Reverse for left side.
Re: What screw goes here? Right air cleaner support
Posted by:
Frank DuVal
()
Date: June 17, 2022 02:00PM
Correctamundo!
Frank DuVal
Fredericksburg, VA
Frank DuVal
Fredericksburg, VA
Re: What screw goes here? Right air cleaner support
Posted by:
PequotMonza64
()
Date: June 17, 2022 05:51PM
Grateful for the responses.
After reading your posts, I found the diagram I had printed out that called out the screw/bolt sizes.
Then I actually found my 3/8-16 tap and was able to chase the threads. I think it was the only non-metric tap still in the kit.
Thanks
Glen in Ohio
1964 Monza Sedan Powerglide 110 hp
Low mileage survivor, stock as delivered
Records back to 1967 in Pequot Lakes, Minnesota
Original dealer Mike Turk's in East Liverpool, Ohio
Located in Cleveland, Ohio area
After reading your posts, I found the diagram I had printed out that called out the screw/bolt sizes.
Then I actually found my 3/8-16 tap and was able to chase the threads. I think it was the only non-metric tap still in the kit.
Thanks
Glen in Ohio
1964 Monza Sedan Powerglide 110 hp
Low mileage survivor, stock as delivered
Records back to 1967 in Pequot Lakes, Minnesota
Original dealer Mike Turk's in East Liverpool, Ohio
Located in Cleveland, Ohio area
Sorry, only registered users may post in this forum.