![]() ![]()
| |||||||||||||||||||
![]() ![]() ![]() ![]() ![]() ![]() |
Corvair Center Forum :
Corvair Center Phorum
![]() Corvair Center Re: looking for pinto motor Posted by:
wittsend
() Date: November 14, 2020 06:59PM Pinto's came with the British Kent 1600 (push rod), the German EAO 2.0 (OHC), and the USA Lima 2.3 (OHC). Which specific engine are you looking for? I have a German EAO 2.0 (flex plate, not flywheel, and a crack exhaust manifold) that "smoked when ran." But I'm in California and it would be WAY too cost prohibitive to ship. Re: looking for pinto motor Posted by:
Caraholic4life
() Date: November 14, 2020 07:23PM I did a quickie search for a 1980 Ford Pinto Engine using the Hollander Exchange website and found one Engine but it is in Texas....MAYBE [www.partshotlines.com] It is listed as 1979 BOBCAT Engine 4-140 (2.3L) (2.3L, vehicle identification number A, 8th digit, 4-140) Stock Number W18F528 at Wichita Falls Motorcars LLC, Wichita Falls , TX 76 866-411-1120 Ext 020743 but no price was indicated. Here is a link for the Hollander Exchange website. It may help. [www.partshotlines.com] For those who may be unaware, Hollander is a system/service that a large number of Junk Yards use to locate parts on a daily basis. 1962 95 F.C. Van 1964 Greenbrier Deluxe 1965 Monza Coupe 1965 Monza Convertible Westminster, Maryland MID ENG enthusiast & prior Kelmark owner. Re: looking for pinto motor Posted by:
MarkDustan
() Date: November 14, 2020 10:32PM The pinto motor goes in the front right? [www.youtube.com] Re: looking for pinto motor Posted by:
MattNall
() Date: November 14, 2020 10:35PM Lots of pinto engines hangin' out the rear off of VW transaxles! MODERATOR Sea Mountain, between Charleston Harbor and Coos Bay! SW Oregon Coast Click HERE for My Website...Click HERE for My TechPages! ..............................110-PG.................................................Webered-Turbo ![]() ![]() Re: looking for pinto motor Posted by:
putput
() Date: November 16, 2020 05:24PM thanks to all it is going in 1931 ford a Re: looking for pinto motor Posted by:
SpyderMan
() Date: November 17, 2020 05:44AM My dad has a pinto cylinder head on a Model T. It runs great. Sam Russell Durham NC 1962 Monza Wagon Ted Brown EFI Gen II 1964 Spyder coupe Re: looking for pinto motor Posted by:
Timothy Shortle
() Date: November 17, 2020 09:17AM My mom used to have a 72 Pinto coupe that had a 2000cc with 4 speed. That car ran damned well back in the day. Re: looking for pinto motor Posted by:
wittsend
() Date: November 17, 2020 10:16AM putput Wrote: ------------------------------------------------------- > thanks to all it is going in 1931 ford a By chance do you have the Shay? Shay WiKi It was a a Model A replica that came out in the late 70's. If so it would have the 2.3 OHC (Lima) engine. "Similar" 2.3 Lima engines were used into the early 90's Mustangs and Rangers. By then they had EFI, roller cams and some with dual plug heads. Re: looking for pinto motor Posted by:
65CorsaTurbo
() Date: November 20, 2020 04:10PM car-part.com has several 4 cylinder ones throughout the country and a few 6 cylinder ones. Bill (B.Y.) 1965 Monza convertible, red/red, white top, 110, auto. 1965 Corsa 180 (under restoration) 1966 500, white/red/110/auto (sold) 1967 Crown V-8 (sold) Pittsburgh, Pa. Sorry, only registered users may post in this forum. |