Corvair DiagramCorvair Photo
Corvair Center
home forum corvairs calendar links Corvair Podcast
California Corvairs
Clarks Corvair
Clarks Corvair
“CORSA"



Chevy Corvair License Plate
Chevy Corvair Chrome Wheel
FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 15, 2020 04:36AM

FoSale: LM Shrouds and other engine parts. Trying to clean out all the engine tins and other parts & pieces I have. I have already moved some tins/parts to the scrap metal pile as they would have taken too much work to repair.

Front Shrouds 65 M/T (2) powder coated $60 plus shipping/insurance.
Front Shroud 65 turbo (1) $40 plus shipping/insurance.
Fan Shrouds 3 - 65s and 5 -66s. 2 66s for 12 plate oil cooler. rest can be cut to fit 12 plate cooler. $25 plus shipping/insurance
Lower Shrouds 3 LM and 1 EM. $30 plus shipping/insurance.

I have lots of other shrouds and seal retainers not photographed, like panels on each end of engine, heat ducts, cooling boxes and side shrouds. Just PM me what you are looking for.

Also selling the following:

2 Thermostat (used) with rods and clips $65 each plus shipping/insurance.
12 push rod tubes painted with high temp VHT silver paint $14 each plus shipping/insurance
Coil bracket painted with high temp VHT silver paint $15 plus shipping/insurance.
Fresh Air Connector painted $12 plus shipping/insurance.
RH Exhaust Shield painted with high temp VHT GM satin black paint $25 plus shipping/insurance

I also have engine top covers, rear covers, oil pans, engine mount brackets, 110 exhaust logs valve covers, used connection rods (12) and other engine pieces that can be had. PM me with what you are looking for. I also have lots of engine hardware.

PM me, if interested in anything above More photos on second post. I will post a photo of the barrel and box holding all the other tins.

forsale

Al
Georgia



Edited 1 time(s). Last edit at 05/31/2020 05:50PM by MattNall.

Attachments:


Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 15, 2020 04:37AM

Rest of photos.

Al
Georgia

Attachments:

Re: FS: LM Shrouds and other engine parts
Posted by: 63ConDan ()
Date: May 15, 2020 10:20AM

PM sent on 2 Thermostat (used) with rods and clips $65 each plus shipping/insurance.

Dan Central MN

1968 Convert

Re: FS: LM Shrouds and other engine parts
Posted by: playerpage ()
Date: May 15, 2020 03:23PM

Dang. That was what I was looking for. tongue sticking out smiley

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 15, 2020 04:36PM

Sale Pending on thermostats& rods. Also on 2 fan shrouds and turbo front shroud.

Here is the barrel and bins of parts I am trying to slim down this next few weeks.

Al
Georgia

Attachments:
Re: FS: LM Shrouds and other engine parts
Posted by: aircooledairhead ()
Date: May 17, 2020 09:31AM

Sent PM about cooling fan in your blue barrel. If you didn't get it, please let me know.
Thanks,

Fred Gillam, southern SC coast
Former Corvairs from teens and 20's.
3 65 Corsa 180 convertibles
63 Spyder
66 Monza 110 PG, "Moldo"
65 Corsa 140
Currently helping son with 65 Monza 140 4-spd coupe

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 17, 2020 09:42AM

Fred:

I have not bead blasted any fans I have in the container to see if they have cracks. I would not sell one without that check first.

How fast do you need one?

Al
Georgia

Re: FS: LM Shrouds and other engine parts
Posted by: aircooledairhead ()
Date: May 17, 2020 10:08AM

Hi Al,
Not a big rush. The one in my son’s car has a small chip out of the edge, no visible cracks. I’d just as soon replace it.
Thanks,
Fred

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 17, 2020 10:57AM

I just looked at that one. It has a crack in it. But I may have one that you might like.

Al
Georgia

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 17, 2020 11:30AM

Fred:

Cooling fan I do have, I will sell. I got this one ready for my Big Valve Engine, but have decided to use the one I painted years ago that is silver metal flake.

Sent you PM on it.

Al
Georgia

Attachments:

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 17, 2020 11:35AM

The two (2) Thermostats (used) with rods and clips are back available

$65 each plus shipping/insurance. PM me, if interested.

Al
Georgia

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 17, 2020 11:59AM

Engine Blower Fan was not picked for buying. Not at budget cost. Very nice fan, though.

Al
Georgia

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 17, 2020 12:06PM

I also have a complete set of LM seal retainers in excellent condition. Plus the angle piece for between the cooling boxes. Painted in past 2 years and protected while in the bin.

$100 plus shipping & insurance.

I also have as removed retainers. I have good corners, fronts and both sides. $6 each.

PM me, if you are interested in these.

Al
Georgia



Edited 1 time(s). Last edit at 05/17/2020 12:09PM by Lane66m.

Attachments:
Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 21, 2020 04:39PM

I finished making some templates to modify fan shrouds for the 12 plate oil cooler, 140 left heat panel and turbo front shroud & right upper shroud. Makes it easy to do it right.

Who knows If they ever be needed, but they are here now. I have used the turbo front shroud template already. If you don't have the real thing to copy off, these will get the job done.

I will be cutting all my fan shrouds to fit the 12 plate oil cooler. Anyone needing a fan shroud for an 8 plate cooler, let me know soon. Cutting will be done this weekend.

Al
Georgia

Attachments:
Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 31, 2020 05:14PM

Bump.

Al
Georgia

Re: FS: LM Shrouds and other engine parts
Posted by: mtmouse ()
Date: May 31, 2020 05:42PM

Al, quick question. When you bead blast the fan to check for cracks do you use glass bead or steel shot to peen it. Also what pressure do you blast at?
Thanks for any info you may pass on.
Joe

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: May 31, 2020 06:30PM

Ultra fine glass bead shot at 80 psi from about 2 -3 inches. Just enough to take remaining dirt and corrosion off (and any remaining paint). I don't do any peening of the magnesium. I try to get most old paint off with thinner or a safe stripper.

Al
Georgia

Re: FS: LM Shrouds and other engine parts
Posted by: mtmouse ()
Date: May 31, 2020 06:42PM

Al, thanks for the help.
Joe

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: June 10, 2020 02:24AM

Painted heat shield has sold.

I still have some as removed heat shields.

Al
Georgia

Re: FS: LM Shrouds and other engine parts
Posted by: Lane66m ()
Date: June 10, 2020 02:37AM

I have modified all my fan shrouds to fit engines with 12 plate oil coolers. They were done using a template. 4 each 65 shrouds and 2 each 66 - 69 shrouds. 65 shrouds can have 6 mount holes enlarged to fit the later car engines.

Al
Georgia

Attachments:
Sorry, only registered users may post in this forum.
This forum powered by Phorum.